I am in need of some basic steps in adding 2 new 3750 switch to an existing VLAN network of Stackable switches. The Stackable switches are 5 (WS-C3750X-12S-S ) in numbers.
I have an idea of what to configure if i was handling a 2950 switch. But this is my first attempt on a 3750 switch and don't want to mess it up.
After connecting these 2 new switches to the existing stack, do they automatically learn their number in the stack before any configuration is done?
Secondly, where will the configuration be done from; is it from the Master switch or directly on the new switch?
Normally on a 2950 switch, you configure it as a client in the existing domain and then configure VTP on the linked Ports between the switches before actually adding them to the network. Does that same rule apply?
by default a new switch
out of the box has a switch number of 1. When they
are added to the stack, the master will assign the number
to the switch. This is automatic, but as I've witnessed
in working with these, if you add two switches as
you are wanting to do, it's possible depending on the
rev of hardware (ie processor), the time it takes for
a switch to initialize and announce itself to the stack
can be different. If you add to switches to a five
stack switch, it's possible for the 7th switch to
actually receive the switch number of 6 because it
comes up first. Maybe I'm just paranoid, but I
like to manually change the switch number
(by doing "switch 1 ren XX" here XX is your new
switch number.
After the new switches are brought into the
stack by the master switch, a few seconds to
a minute or two later, the master will shadowcopy
the configuration down to the new members of the stack.
As TomS mentioned, the configuration is taken care of
from the management IP, which the master switch of
the stack will answer to.
You can tell the master two ways, either from the
status light on the front of the switch, or by
doing a "sh sw detail".
If you choose to view from the front of the switch,
you can also push the status button until you have
the stack light lit. At this point each switch in
the stack will flash one of the LED status lights for
the 10/100/1000 (if applicable) ports. This light
port number will reflect the switches number.
Example, switch 1 will flash the Fa1/0/1 light,
switch 2 will flash the Fa1/0/2 LED and so on.
You'll also not that the LED's of your last two
SFP ports will also light. If you have a 48 porter
Gi1/0/3 and Gi1/0/4's lights will light up Green
or Amber. IF you have a 24 port you only have
2 SPF ports unless you have a 3750G model.
These lights tell you the status of your Stackwise
cables and your 32Gig ring. If the ring is intact
both green lights will be on. If there is an issue
with the stackwise cables, one or both of the lights
will be amber. The amber lights show which switches
have issues. The stackwise cables can be touch at times.
If you use the "sh sw detail" you'll get an output like
this;
nocsw064#sh sw
Current
Switch# Role Mac Address Priority State
--------------------------------------------------------
1 Member 0017.941d.a780 15 Ready
*2 Master 0014.698c.af00 10 Ready
3 Member 0011.9307.c480 1 Ready
4 Member 0011.930f.8d80 1 Ready
5 Member 0011.930f.7880 1 Ready
6 Member 0011.930f.9a00 1 Ready
Stack Port Status Neighbors
Switch# Port 1 Port 2 Port 1 Port 2
--------------------------------------------------------
1 Ok Ok 2 3
2 Ok Ok 1 4
3 Ok Ok 5 1
4 Ok Ok 6 2
5 Ok Ok 3 6
6 Ok Ok 5 4
this shows many things, 1) how many switches
are part of the stack and their stack numbers,
2) who is master of the stack, 3) the priority
settings of each switch in the stack.
If you notice in the above, switch 1 has a priority
of 15 with when the stack is coming up, basically forces
switch 1 to be the master. Switch 2 has a priority of
10, which means if something happens to the master
switch 2 will take over the role of stack master.
If you notice there is a '*' next to switch 2's number.
This means it's currently the stack master, since
we had a issue with the master.
If you don't hard code the priority, any switch
in the stack can take over for the master. This
is decided in a election process similar to how a
master browser in windows is elected. UPtime, IOS
rev, MAC address and a few other factors come into
play. Instead of letting this happen we prefer to
hard code.
With the "sh sw detail" you'll see the second
part of the output shows the status of the stackwise
ports as well.
Also one more thing I remember, but didn't mention
earlier. If you're going to use etherchannel to
bundle Fa or Gi ports, this will act the same as
it does on the other switches, with the exception
in the case where you want to bundle ports between
ports of one or two other switches, you'll have to
mess with the WS-C3750V2-48PS-S PAg protocol, but it is possible.
2014年3月3日星期一
2014年2月23日星期日
Newbie choice of Cisco 1900 vs 2900
I
have a small office network with 10/100mbps NICs in 15 computers as
well
as a few network printers and netcams. The server is running
Windows
2003 and SQL 2000 and also has a 10/100mbs NIC. The database is
somewhat traffic intensive.
I
have come into possesion of a Cisco Catylyst Cisco 1900 and a separate
2900.
Would there be an advantage to using one of these switches over
the other in this situation?
In
article <(E-Mail Removed) .com>,
rbob
<(E-Mail Removed)> wrote:
:I
have a small office network with 10/100mbps NICs in 15 computers as
:well
as a few network printers and netcams. The server is running
:Windows
2003 and SQL 2000 and also has a 10/100mbs NIC. The database is
:somewhat traffic intensive.
;I
have come into possesion of a Cisco Catylyst 1900 and a separate
;2900.
Would there be an advantage to using one of these switches over
;the other in this situation?
1900: 10 Mbit ports except for 2 uplinks; runs CatOS
2900:
10/100 ports, some models have gigabit; some models run IOS;
some
models have Layer 3 operations (i.e., routing); some models
have QoS and rate limiting
2900
covers a large range of capabilities -- too large a range to
use
as a family designator. The 2901/2902 were very different than
the
2948G-L3, and quite different again from the 2950. The 2950 is
a current model; the 2901 went end-of-sale in 1999.
I
guess my question is with a small network such as mine I could use
the
24 ports of the Cisco 3925E compared to the 12 ports of the 2901 but would
there
be any speed difference (10mbps of 1900 vs 10/100mbps or 2901) ?
2014年2月18日星期二
Cannot Find ADSL Firmware 4.0.0.18 for Cisco 1801
I
have a number HWIC-1T of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A
Wholesale Broadband Connect [WBC] services. The routers are experiencing
connectivity issues. There is a cisco product bulletin that defines v4.0.0.18
as the version of ADSL Firmware required on the Cisco 1801 when connecting to
this BT service.
I
would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on
CCO. All the 4.0.0.18 downloads appear to
be for various flavours of 800. The Cisco product bulletin shows the
1801 as having the same chipset as the 857,867,877 and 887. Can I use the
Firmware from one these 800 models? The MD5 Hash for the code suggests all of
the these 800 model use the same code?
Has
anybody seen this problem with the Cisco 1801 or upgraded the Firmware to
4.0.0.18.
Yes, the 1801 use same HW and FW as the 800
and the WS-X45-SUP7L-E
2014年2月12日星期三
3750 Connectivity issue
I
have a WS-C2960G-24TC-L
with
a 1000base LX SFP
connected
via single mode to an Incomming gigabit circuit from SSE/Telco (Scottish and
Southern Electric)
this
configuration works ok.
When
i move the connection to a WS-C3750X-12S-S (with the same sfp) i get no
connectivity, no physical or anything,
has
anyone seen this before when i do a show interface it does nothing, not
connected etc.
Any top tips and handy hots would be appreciated
GigabitEthernet0/22
is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is
0023.052b.a096 (bia 0023.052b.a096)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload
1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 1000Mb/s, link type is auto,
media type is 1000BaseLX SFP
input flow-control is off, output
flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:09, output 00:00:00, output
hang never
Last clearing of "show interface"
counters never
Input queue: 0/75/0/0
(size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 108000 bits/sec, 64
packets/sec
112643 packets input, 51674930 bytes, 0 no
buffer
Received 54673 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
1 input errors, 1 CRC, 0 frame, 0 overrun,
0 ignored
0 watchdog, 54638 multicast, 0 pause input
0 input packets with dribble condition
detected
56007230 packets output, 26626201288
bytes, 0 underruns
0 output errors, 0 collisions, 5 interface
resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE
output
0 output buffer failures, 0 output buffers
swapped out
-------------------------------------------------------------------------------------------------
sh
int gi1/0/25
GigabitEthernet1/0/25
is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is
2893.fe02.5119 (bia 2893.fe02.5119)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10
usec,
reliability 255/255, txload 1/255, rxload
1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto,
media type is 1000BaseLX SFP
input flow-control is off, output
flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 21:19:20, output 21:19:20, output
hang never
Last clearing of "show interface"
counters never
Input queue: 0/75/0/0
(size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0
packets/sec
21 packets input, 2890 bytes, 0 no buffer
Received 21 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun,
0 ignored
0 watchdog, 21 multicast, 0 pause input
0 input packets with dribble condition
detected
22 packets output, 3480 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface
resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE
output
0 output buffer failures, 0 output buffers WS-C3750V2-48PS-S swapped out
Cisco 3560 IOS problem
I
have a WS-C3560X-24T-L switch and I am getting the following error.
Base
ethernet MAC Address: 00:1f:c9:96:60:80
Xmodem
file system is available.
The
password-recovery mechanism is enabled.
Initializing
Flash...
flashfs[0]:
452 files, 6 directories
flashfs[0]:
0 orphaned files, 0 orphaned directories
flashfs[0]:
Total bytes: 15998976
flashfs[0]:
Bytes used: 2176512
flashfs[0]:
Bytes available: 13822464
flashfs[0]:
flashfs fsck took 8 seconds.
.done
Initializing Flash...
Boot
Sector Filesystem (bs) installed, fsid: 3
done.
Loading
"flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbasemz.122-35.SE5.bin"...flash:c3560-ipbase-mz.12
2-35.SE5/c3560-ipbase-mz.122-35.SE5.bin:
no such file or directory
Error loading "flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin"
Interrupt
within 5 seconds to abort boot process.
Boot
process failed...
The
system is unable to boot automatically. The BOOT
environment
variable needs to be set to a bootable
image.
Things which i have already tried:
switch:boot
Loading
"flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin"...flas
h:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin:
no such file or dir
ectory
Error loading "flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin"
Interrupt within 5 seconds to abort boot process.
When
i issue Dir i got the following msg:
List of filesystems currently registered:
flash[0]:
(read-write)
xmodem[1]:
(read-only)
null[2]:
(read-write)
bs[3]:
(read-only)
Also
Tried dir flash
unable to stat flash/: no such device
I also have ios of that switch and when i am trying to push through X modem i got below msg:
Unknown cmd: Š **B0**B000000000022d
switch:
Š*00000002d
Unknown cmd: Š*00000002d
switch:
Š**B000000000022d
Unknown cmd: Š**B000000000022d
switch:
Š**B000000000022d
Unknown cmd: Š**B000000000022d
switch: Š**B000000
1)
flash_init
2) load_helper
Next you need to change the baud rate on the switch, otherwise it will take about 2 hours to transfer the IOS via xmodem.
3) set BAUD 115200
After you issue the baud rate command on the switch make sure you also change it in Hyperterminal or whatever software terminal emulation software you use. Otherwise you won't be able to communicate to the switch.
4)
copy xmodem:"image_filename.bin" flash:"image_filename.bin"
5)
In Hyperterminal select "Transfer" and select "send file".
Change the protocol to xmodem. Next select browse and navigate to where you
have stored the IOS that you would like to transfer to the WS-C3560X-24T-S switch. Click send.
2014年2月10日星期一
cisco 3560 router or switch!
Opmanager
7 (fresh install, latest version, plenty of server power) has decided to
randomly categorise my cisco WS-C3560X-24T-L series switches as either 'router' or
'switch' depending on its mood.
The
ones classed as router come up as 'cisco device' even though in the description
field below that box it says 'cisco 3560...blah blah'.
If i then go and change the device type to 'cisco 3560 series switch' i either get page that says 'error' or 'device cannot be found'.. if its the latter its been deleted from the database and i can't re-add it as its partially there....
While adding the device, we will match the sysoid on the device template and based on it, the device type will be applied. So if there are no templates for the device it might be associated wrongly. So to make the cisco 3560 device fall under the right category, create a new template by following the steps in this LINK. Now you can apply the template to all the 3650 devices and it should work fine.
For the device being partially added, follow the steps in this LINK which will remove the device completely from the database. Now add the device again and it should be fine. We will make this template available out of box soon.
If you have the device template already, then you don't have to create one. You can go to the particular template under Admin --> Device templates and apply it to all the cisco 3560 devices. While discovery, if you have multiple credentials selected or if the response for the SNMP request from the device is slow, then it might get timed out and fall under the general cisco device category. Applying the right template all the devices will move to the correct category.
now
running a completely clean copy of opmanager, fresh install.
Added
6 devices. 5 of the 3560's went in fine. One became a router so i tried to
manually tell it the device was a WS-C3560X-24T-S and now its vanished again and i can't
re-add as apparently its already in the dbase..
2014年2月9日星期日
Adding new 3750 to stack without provisioning config?
I currently have 3 WS-C3750X-48T-L in a stack, and would like to add another as a slave. I have read the documentation on Cisco's website, and tutorials on various other websites, and just have a couple of points I would like to clarify before I go ahead.
My main question - is there actually any need, or is it recommended, to use the "switch 4 provision ws-c3750-48p" command before doing the physical connection of the 4th switch to the stack? According to Cisco, this will be done automatically when the new switch is connected anyway?
If I do use that command on the stack before connecting, do I also need to use the command "switch 1 renumber 4" on the new switch before adding it to the stack? Some documentation seems to suggest that it will automatically be assigned to the stack as switch 4, as long as it is the correct type of switch (specified in the provision command on the stack), while other documentation seems to suggest that the number also has to match before it is connected - but maybe I'm reading it wrong!
Another
thing I would like to check before going ahead.. at the moment, the switches
are connected as follows:
Switch Port 1
Port 2
1 2 3
2 3 1
3 1 2
To
physically add switch 4 to the stack, my plan would be to first disconnect the
cable between switch 3 and switch 1. Am I right in thinking that this should
not affect the operation of the 3 existing switches/stack, since switch 1 will
still be connected to switch 3 via switch 2?
Then, the plan would be to connect the two ports on switch 4 to the now-empty ports on switches 1 and 3 (where the cable that I removed in my previous step used to be), and power it on.
If anyone can clarify this for me, or has any other advice, it would be much appreciated - thanks!
The provision command is useful for PRE-provisioning a switch prior to adding it to a stack. In this way, you can configure all of the switch ports before the switch is ever "really" added. You're right that the switch will automatically do this upon stacking it, however it will be a blank configuration.
To add an additional switch to your stack, please first ensure the stack-ring is in a full-duplex ring. This can be verified via the command: "show switch stack-ring speed". Once you remove one stack cable between switch 1 and 3, the stack will become half-duplex, this is fine for a temporary period of time.
I
would take the connection going to switch 3 from switch 1 and put that in your
new switch. Then add a new stack cable between WS-C3750X-48T-S switch 3 and 4. Then power your
new switch on and ensure your stack ring is in a full duplex ring.
2014年1月23日星期四
Newbie connecting DELL 6248 stack to CISCO 3750 stack
I
need to extend the office LAN by connecting an existing CISCO WS-C3750X-12S-S stack to a
new DELL 6248 stack.
I
intend to use the fibre/combo port In DELL 6248 to connect to CISCO uplink
port.
I
want to use DELL port 48 but I saw there were 1/g48 and 1/xg48. From memory, they are mutually exclusive.
Q1. Does it mean I will just configure 1/g48 and
don't bother going into the config of 1/xg48?
Q2. To connect the 2 stacks together, should I
just define both connecting ports as trunk port? I have no experience in doing that. FYI.
We are using VLANs in the CISCO stacks already and so the new DELL
stacks need to know about it.
I
was able to connect the 2 stacks together, but I am not sure if what I did was
correct.
On
the existing CISCO stack, I have been using VLAN 1 as the data (untagged) and
VLAN 100 as voice (tagged).
On
the new DELL stack, I defined 1/g48 (fibre port) as access port and VLAN 100 as
the default untagged VLAN.
On
the existing CISCO stack, I leave the Gigabit 1/0/4 port to its default which
happens to be access mode with 1 as the default VLAN.
I
thought what I did was incorrect but anyway I thought I still gave it a go and
I was able to plug a PC into the DELL stack and do the normal "data"
stuff without any problems.
Q1. So, does it mean that even if the VLAN nos do
not match on the connecting ports, it does not really matter?
Is
this correct?
a)
On the DELL stack, I configured the 1st fibre port as below:
#show
interfaces switchport ethernet 1/g48
Port:
1/g48
VLAN
Membership mode:Access Mode
Operating
parameters:
PVID:
100
Ingress
Filtering: Enabled
Acceptable
Frame Type: Untagged
Default
Priority: 0
GVRP
status:Disabled
Protected:Disabled
Port
1/g48 is member in:
VLAN Name Egress rule Type
---- ---------------------------------
----------- --------
100 Data Untagged Static
Static
configuration:
PVID:
100
Ingress
Filtering: Enabled
Acceptable
Frame Type: Untagged
Port
1/g48 is statically configured to:
VLAN Name Egress rule
---- ---------------------------------
-----------
100 Data Untagged
Forbidden
VLANS:
VLAN Name
---- ---------------------------------
b)
On the CISCO stack, I configured the fibre port as below:
Name:
Gi1/0/4
Switchport:
Enabled
Administrative
Mode: static access
Operational
Mode: static access
Administrative
Trunking Encapsulation: negotiate
Operational
Trunking Encapsulation: native
Negotiation
of Trunking: Off
Access
Mode VLAN: 1 (default)
Trunking
Native Mode VLAN: 1 (default)
Administrative
Native VLAN tagging: enabled
Voice
VLAN: none
Administrative
private-vlan host-association: none
Administrative
private-vlan mapping: none
Administrative
private-vlan trunk native VLAN: none
Administrative
private-vlan trunk Native VLAN tagging: enabled
Administrative
private-vlan trunk encapsulation: dot1q
Administrative
private-vlan trunk normal VLANs: none
Administrative
private-vlan trunk private VLANs: none
Operational
private-vlan: none
Trunking
VLANs Enabled: ALL
Pruning
VLANs Enabled: 2-1001
Capture
Mode Disabled
Capture
VLANs Allowed: ALL
Protected:
false
Unknown
unicast blocked: disabled
Unknown
multicast blocked: WS-C3750V2-48PS-S disabled
Appliance
trust: none
Cisco 3750 =>blocking dhcp trafic on an interface
At
work I've got a cisco WS-C3750V2-24PS-S switch and few end devices which of course are
company proprietary, connected to this switch in a separate VLAN. Now these end
devices generate dhcp traffic "request" and is being propagated
across all the sites where these devices are connected.
Now I've been reading stuff about dhcp
snooping features which is great but in this instance these end devices don't
have a DHCP server. In this scenario all these end end devices have got static
ip addresses allocated.
Also my senior engineer being very narrow
minded wants me to implement this change only on the interface level and not on
the configuration level.
Can someone please confirm if I can just
only enable "ip dhcp snooping trust" on the interface level which i
believe will stop the dhcp traffic ??
I'd
only enable "ip dhcp snooping Vlan 10" in the global config.
So
after enabling "ip dhcp snooping Vlan 10" in the global config , the
switch will only stop DHCP traffic, correct ??
I
am a little pedantic since i've never performed this setting on a cisco WS-C3750X-24P-S switch
before and would really appreciate input of experienced people !!
2014年1月21日星期二
Configuring SNMPv3 for Cisco 3560X
I
am using OpManager ver 9101.
Recently
installed a Cisco WS-C3560X-24T-L switch and wanted to test using SNMPv3 to manage the
switch.
The
following are the commands used on Cisco 3560X:-
snmp-server
group OpMgrGrp v3 priv
snmp-server
user OpMgrUser OpMgrGrp v3 auth sha ABC priv aes 128 DEF
snmp-server
context opmanager
I
created the credentials using OpMgrUser with SHA ABC and AES DEF, and context
opmanager in OpManager.
Then
try to add device, but it is trying until timeout and failed to add the device.
If
I use the following command, then OpManger added the device successfully.
snmp-server
community public RO 99
Which
context name should I put in OpManager credential?
If
you have followed the KB WS-C3560X-24T-S , you can leave it blank.
Cisco Catalyst 3750 PoE Issue
we
have a 3-switch stack (1x WS-C3750V2-24PS-S 48-port w/no PoE on top, and 2x 3750 48-port
PoE underneath). We have PoE IP phones that are all functioning. I recently
acquired 2 Engenius EAP9550s to add as repeaters for an expansion of our
office. When I connect the APs (in PoE mode on the switches), the indicator for
each AP turns green and the APs power up, briefly.
After
about 10 seconds, the indicator LED on the switch turns amber. At this point,
almost all of the indicators are amber on this bottom switch, they all changed
to amber after I tried the APs in them. We have about 5 PoE phones connected to
it (the remainder are on the middle PoE 3750)
The
device specs state that each AP runs at about 18W (48 VDC x 375 mA)
I
can't imagine that I am hitting my wattage limit per switch with the small
number of phones that are connected to that particular switch, but the
indicator code seems to imply the switch is denying PoE for these ports due to
the 350W limit. I don't see any voltage limits in the spec sheet for the switch
so I am at a loss.
So,
when the switches are stacked, is there a different limit? Or does each switch
have its own individual limit? Do I need a booster? I was under the impression
the APs would function fine, we have a separate AP on a different physical
network with the identical switch setup and it works just fine. PoE is enabled
in the port specifications for every port on all of our PoE switches (its the
default but I double-checked to be sure).
Do
you actually need Power over Ethernet for all of the ports that have it active?
If not turn off the extras as you don't need the power drain...
Are
these switches connected to a UPS system and is that system throwing any
warnings or errors? It could be that you are actually running out of available
power with all the ports and switches and such connected in the same place...
Also,
how is the power getting into the switches? You're not trying to chain feed it
from one to the next right? They each have their own AC adapters correct?
We
need the option since the IP phones we have are pass-through switches for our
non VoIP traffic - i.e. VLAN 9 - VoIP, VLAN 8 Data, both through the same port
and it needs PoE for the phone to power on and provide the passthrough
switching.
We
have 3 UPSs running at 30% capacity each according to the management consoles,
no warnings. That was the first thing I checked, each switch is plugged
directly into a PDU and it is all load balanced, no chaining at all.
If
there is a non-PoE (or no device at all) plugged into the PoE switch, does it
drain more power than designating the port as non-PoE? I thought the switches
automatically determined power requirements.
I
figured the same thing regarding the circuit, but there is nothing else plugged
in to this particular switch aside from 5 PoE IP phones and the 2 APs.
Switching
the positions of the switches would be a task, so I haven't tried it. I picked
up 2xGb PoE Boosters for cheap to see if they fix the problem. Thinking about
the stack, they are all trunked, but they each have dedicated power supplies so
I can't imagine the stack would have a more limited Wattage than the sum of the
3 switches WS-C3750X-24P-S . We shall see, thanks for helping me brainstorm!
2014年1月20日星期一
Ios update for 3560-C
I
plan to buy WS-C3560X-24T-L (Catalyst 3560-C) for my home lab. I just created
a new account on cisco.com (I did not register any equipment or contract for
that new account). I was able to download ios 12 and 15 for that switch.
Will
I be able to flash one of these versions when I will have the new switch ?
Cisco
warranty for these Switchs (Enhanced Limited Lifetime Hardware Warranty,
www.cisco-servicefinder.com/warrantyfinder.aspx) says NO OS Software Updates
included. Does tha mean that I can download ios updates but won't be able to
flash the device or use it ?
-
Do I really have to buy Smartnet support to be able to update ios for that
switch ?
Hello
just to answer some of your points.
-
Everybody with an cisco account and without contract can download universal
ios. The universal ios file can't be used without an proper license. So it
doesn't matter
Maybe
this is the case, may just come with a base feature set. Ip base or LAN base?
-
3560CG comes with an IP Base license and can't be upgraded to IP Services
It
can be upgraded to ip services. You need the correct image or license,
depending on which major version you go with, I.e. 12 or 15.
12
you can download the correct firmware with the feature set, with 15 you need a
license.
-
So I suppose that I will be able to update 3560CG with any universal ios
version and "stay" at IP Base level
Depending
on what feature set the universal image has without licenses. I assume its
base.
-
Smartnet is required if you need support (TAC) or quick (4, 8 hours) hardware
replacement
Yes
I believe so, although I think the thing you call smartnet, I call Cisco
service support contract..?
-
Smartnet is not required for normal (days) hardware replacement as WS-C3560X-24T-S warranty is lifetime of the product (except power for 5 years)
This
information should all be in the service support contract.
订阅:
博文 (Atom)